Revision as of 16:27, 22 February 2015

technology level III

• (folding)
• Assembly levels give a great aid in nanofactory design. & Tooltip preparation zone - Mechanosynthesis core - DME assembly robotics
• Design levels
• Control levels

Basic energy balance

As carbon carrying resource material the fuel gas methane (CH₄) or the welding gas acetylene (C₂H₂) is used. When those gasses are not burned but are being put together to products there still remains a lot of excess energy.

• heating values: CH4 55,5MJ/kg > C2H2 49,9MJ/kg > Cn 32,8MJ/kg (graphite)

As resource material the carbon carrying "exhaust-gas" carbon dioxide CO₂ in ambient air can be used too. Its like "ash" on the lowest end of the carbon combustion chain thus the heating value of zero. If it is used as building material high amounts of energy are needed.

• heating values: CO2 0,0MJ/kg < Cn 32,8MJ/kg (graphite)

Personal fabricator as stationary device

Depending on the used building material the needed or excessive energy must be taken from of fed into the electric grid. Gas lines (CH₄) and atmospheric CO₂ lend themselves as existing building material supply.

Personal fabricator as portable device

Huge amounts of energy cannot be provided from the small device. The resource-gasses (e.g. CH₄ or C₂H₂ in capsules) must thus carry along enough energy for production. Simply radiating excessive heat away may slow down production significantly because of the high chemical energies involved. It may be better to balance the excess energy roughly to zero by using atmospheric CO₂ as building material too. To pump high volumes of air silent medium mover metamaterials can be used.

Convergent assembly

• Convergent assembly (putting things together in a hierarchical way) is not a means to speed up production in general.
  
• Do not confuse convergent assembly with exponential assembly which is an entirely different thing.
• Go to the convergent assembly page to see what motivates the use of convergent assembly.
• The lowermost three convergent assembly steps follow naturally from the character of the technology - see assembly levels to understand this.

Nanosystem units

Robotic manipulators

Threading by systems

Cooling, vacuum and other logistics

• Vacuum handling
• Thermal isolation & Diamondoid heat pump system

Macroscopically separating design considerations

assembly level 0 splits up in capturing resource molecules from liquid phase by sorting mills and mechanosynthetic peparation. It makes sense to do the former in a warm and the latter in a cold environment. Makorscopic separation (possibly in seperate devices) can be considered. (Aerogel?)

• cooling & isolation

Although diamondoid mechanosynthesis works at room temperature cryogenic cooling will probably be employed just because it seems rather easy to do (see: "Diamondoid heat pump system") and error rates can be shrunken by many orders of magnitude.

General nanofactory design method

Given a set of "base units" for different components of the bottommost assembly levels their combination to form a full nanofactory unit can be determined by first finding the relevant quantitatively or at least qualitatively (set of choices) of evaluable relevant metrics and determine numbers of base units and branching factors based thereof. (constraint logic programming - prolog library clpqr?) might be useful. level throughput balancing output frequency of an assembly level == input frequency of the assembly level directly above

Design metrics

Performance limits

The ultimate performance limit is determined by the accepted dissipation heat at the lower levels the maximal acceptable accelerations at the higher convergent assembly levels. Designs leading to practical speeds at human scale lie way below the performance limits.

power dissipation is only a limiting factor at the bottommost assembly levels. At higher assembly stages bearing area per volume drastically falls. (dynamic drag and breaking losses)

Threading by pre-products

Depending on whether general purpose mechanosynthetic fabricators or mill style fabricators (serial chain of tools with no spaces) are used predominantly more or less layers and channels for threading parts by are needed [?].

Speed limit at the bottom

Low density of actual mechanosynthesis locations are the reason why the bottom layers in a nanofactory need to be stacked up. SVG

slow speed of assembly level 0: The mechanisms to assemble parts normally can potentially be smaller than the parts being assembled. Since The mechanisms to assemble minimal sized DMEs need themselves to be DMEs the mechanisms must have a similar size as the products they assemble. Since only a vew atoms are added per assembly step the density of actual building sites of atomic size is rather low and consequently mechanisms at the bottommost layers are quite a bit slower than the ones above and need to be included in greater numbers.

If assembly units of an assembly level produce (pre-)products slower than the size-characteristic frequency the next higher assembly level demands one can stack assembly units and thread by finished (pre-)products. Assembly units can be stacked as long as the size characteristic frequency of the threading by mechanics is not exceeded.

Ratios between levels

Layer and stage ratios: In any convergent assembly step a step size can be chosen. Big steps limit the maximum possible speed of the considered assembly level step but makes planning and programming more flexible and easier.

Influences of the branching factor

Branching factor: A branching factor of port area to block volume = n²/n³ leads to perfect size and frequency matching in an easy to design 3D iteration extruded 2D fractal design. Other ratios lead either to inefficient port space frequency and under used / under utilisized assembly levels or require 3D fractal designs that are more difficult to design. (There is no scale invariant design as baseline possible then)

Influences of assembly style

In any convergent assembly step one can choose from the different robotic manipulators to do the assembly. Mill style can (with the exception of the bottommost asselmbly level) have the smaller size and higher characteristic operation frequency of the lower assembly level. Single manipulator style assembly have the bigger size and smaller characteristic frequency of the upper assembly level. (Intermediate forms are possible). The choice depends on whether programmability or speed is the the primary concern.

More complicated geometries

non stratified 3D fractal designs need higher convergent assembly stages (assembly level IV) to hold the structure together. They have the highest possible performance (way above practically needed levels) other limits are likely to kick in at some point. Finding a general design methodology seems to be a hard problem.For physical changes of such a design a complete microcomponent disassembly end reassembly is likely necessary.

External links

Articles from E. Drexlers Blog:

• Complete molecular manufacturing systems will have many subsystems, designed to meet many constraints
• Physical scaling laws enable small machines to be highly productive

External references

• Nanosystems chapter 14