Difference between revisions of "Hyper high throughput microcomponent recomposition"
From apm
(added new section == Main restrictions == and link to macroscale slowness bottleneck) |
(big extension) |
||
| Line 8: | Line 8: | ||
The maximum of throughput-performance is likely expectable for the smallest size scale where | The maximum of throughput-performance is likely expectable for the smallest size scale where | ||
* the energy turnover is not yet excessive | * the energy turnover is not yet excessive | ||
| − | * bearing surface area is | + | * bearing surface area is not increased – Note: in first approximation of [[convergent assembly]] total bearing surface area does NOT grow going down the [[assembly layers]]!! |
| − | + | ||
| + | And this would be [[microcomponent recomposition]] processes. <br> | ||
This may lead to astounding and (if not handled properly) even dangerous levels of throughput. | This may lead to astounding and (if not handled properly) even dangerous levels of throughput. | ||
| Line 15: | Line 16: | ||
* The microcomponents that are to be assembled must already be available in a pre-produced state. | * The microcomponents that are to be assembled must already be available in a pre-produced state. | ||
| − | * If product removal | + | * If product removal can't be made faster than the assembly motions then one gets hard limited by the [[macroscale slowness bottleneck]] <br>For more details on this see the explanation on the page: [[Producer product pushapart]] |
| + | |||
| + | == The needed cooling monstrosity == | ||
| + | |||
| + | Going to the absolute limits cooling devices may become much bigger than the actual production devices. <br> | ||
| + | May even the friction of the cooling capsules that are shot through become relevant?? | ||
| + | |||
| + | == It's not a factory, it's a thing shooting rocket/gun! == | ||
| + | |||
| + | If product extraction channels ... | ||
| + | * are well supported (big [[chamber to part size ratio]] and thick walls) and | ||
| + | * do not curve but go straight | ||
| + | ... then product removal speeds can exceed the [[unsupported rotating ring speed limit]]. That is: exceed ~3km/s <br> | ||
| + | |||
| + | This sounds more like a rocket engine than a production device ... lunatic ... <br> | ||
| + | So you better do that in vacuum! <br> | ||
| + | |||
| + | '''In space:''' | ||
| + | * Where to get all the pre-producted microcomponents from? | ||
| + | * What about the intense recoil? "Producing" both ways? <small>(it's more like "produshooting")</small> | ||
| + | |||
| + | '''On the ground:''' | ||
| + | * How to catch the products safely?! | ||
| + | * The whole cooling and catching stuff will likely be bigger than producing the stuff more slowly but with more devices. <br> So what about just producing stuff at sane speeds ... | ||
== Related == | == Related == | ||
Revision as of 16:54, 21 August 2021
Microcomponent recomposers might be able to feature astounding to frightening levels of throughput capability.
Due to:
- (1/2) the scaling law of higher throughput of smaller machinery and ...
- (2/2) the lower energy turnover and higher efficiency of microcomponent recomposition compared to piezochemical mechanosynthesis
The maximum of throughput-performance is likely expectable for the smallest size scale where
- the energy turnover is not yet excessive
- bearing surface area is not increased – Note: in first approximation of convergent assembly total bearing surface area does NOT grow going down the assembly layers!!
And this would be microcomponent recomposition processes.
This may lead to astounding and (if not handled properly) even dangerous levels of throughput.
Contents
Main restrictions
- The microcomponents that are to be assembled must already be available in a pre-produced state.
- If product removal can't be made faster than the assembly motions then one gets hard limited by the macroscale slowness bottleneck
For more details on this see the explanation on the page: Producer product pushapart
The needed cooling monstrosity
Going to the absolute limits cooling devices may become much bigger than the actual production devices.
May even the friction of the cooling capsules that are shot through become relevant??
It's not a factory, it's a thing shooting rocket/gun!
If product extraction channels ...
- are well supported (big chamber to part size ratio and thick walls) and
- do not curve but go straight
... then product removal speeds can exceed the unsupported rotating ring speed limit. That is: exceed ~3km/s
This sounds more like a rocket engine than a production device ... lunatic ...
So you better do that in vacuum!
In space:
- Where to get all the pre-producted microcomponents from?
- What about the intense recoil? "Producing" both ways? (it's more like "produshooting")
On the ground:
- How to catch the products safely?!
- The whole cooling and catching stuff will likely be bigger than producing the stuff more slowly but with more devices.
So what about just producing stuff at sane speeds ...
