Difference between revisions of "Infinitesimal bearing"
m (Apm moved page Infinitesimal bearings to Infinitesimal bearing: plural -> singular) |
(added "macroscopically thin" note & link to superlubrication & other slight improvements) |
||
| Line 3: | Line 3: | ||
[[File:Infinitesimal-bearing-sketch.png|speed distributions from conventional to infinitesimal bearing|frame|From classic to infinitesimal bearings. More layers reduce the relative speed differences. The result has lower friction and higher damage tolerance.]] | [[File:Infinitesimal-bearing-sketch.png|speed distributions from conventional to infinitesimal bearing|frame|From classic to infinitesimal bearings. More layers reduce the relative speed differences. The result has lower friction and higher damage tolerance.]] | ||
| − | To reduce the relative speed of two surfaces one | + | To reduce the relative speed of two surfaces one stacks many layers with minimal thickness (each layer un-percievably small - thus "infinitesimal"). Just enough to accommodate some necessary nanomechanics. Those nanomechanics are [[diamondoid molecular elements|DMME]] gears (not bearings) and further structure that make sure that every layer takes the same part of the total speed difference. Note that due to [[superlubrication]] a single layer can take well perceivable macroscopic speeds without being destroyed thus bearings replacing todays macroscopic ones will need to use only a very thin stack of infinitesimal bearing layers. Since there's no static friction and very low speed dependent dynamic friction in diamondoid nanomechanics (see [[superlubrication]]) the bearings efficiency can be expected to be exceptional. |
It is '''to investigate''' how a macroscopic infinitesimal bearing performs relative to nanoscopic [[diamondoid molecular elements|DMME]] bearing and how long an infinitesimal brearing of certain size would turn till it e.g. reaches half its initial speed. | It is '''to investigate''' how a macroscopic infinitesimal bearing performs relative to nanoscopic [[diamondoid molecular elements|DMME]] bearing and how long an infinitesimal brearing of certain size would turn till it e.g. reaches half its initial speed. | ||
| − | As in all products of advanced nanosystems the nanomechanics must (through their structure) provide some redundancy making the design more complicated | + | As in all products of advanced nanosystems the nanomechanics must (through their structure) provide some redundancy making the design more complicated <br>'''[TODO add more detailed Model]''' |
== Related AP metamaterials == | == Related AP metamaterials == | ||
| − | Adding [[chemomechanical converters|chemomechanical]] or [[electromechanical converters|electromechanical]] motors into the layers changes it into an [[interfacial drive]] (an ''active'' [[metamaterial]]). There the | + | Adding [[chemomechanical converters|chemomechanical]] or [[electromechanical converters|electromechanical]] motors into the layers changes it into an [[interfacial drive]] (an ''active'' [[metamaterial]]). There the add-up of layer movement acts as one of the methods to accumulate nano motion to macroscopic levels ([[mechanical macroscopification]]). |
Revision as of 08:25, 12 April 2014
APM in T.Level III may enable us to create a new type of macroscopic bearings in the form of a passive metamaterial.
To reduce the relative speed of two surfaces one stacks many layers with minimal thickness (each layer un-percievably small - thus "infinitesimal"). Just enough to accommodate some necessary nanomechanics. Those nanomechanics are DMME gears (not bearings) and further structure that make sure that every layer takes the same part of the total speed difference. Note that due to superlubrication a single layer can take well perceivable macroscopic speeds without being destroyed thus bearings replacing todays macroscopic ones will need to use only a very thin stack of infinitesimal bearing layers. Since there's no static friction and very low speed dependent dynamic friction in diamondoid nanomechanics (see superlubrication) the bearings efficiency can be expected to be exceptional.
It is to investigate how a macroscopic infinitesimal bearing performs relative to nanoscopic DMME bearing and how long an infinitesimal brearing of certain size would turn till it e.g. reaches half its initial speed.
As in all products of advanced nanosystems the nanomechanics must (through their structure) provide some redundancy making the design more complicated
[TODO add more detailed Model]
Related AP metamaterials
Adding chemomechanical or electromechanical motors into the layers changes it into an interfacial drive (an active metamaterial). There the add-up of layer movement acts as one of the methods to accumulate nano motion to macroscopic levels (mechanical macroscopification).
