Difference between revisions of "Suitable mechanisms"

Revision as of 18:35, 17 May 2023

This page is basically just a list of mechanisms that
could be useful for future advanced diamondoid gemstone based nanosystems.

Unlike in macroscale machinery with machine parts at the lowermost possible size limit
there is no space for tiny screws that are much more tiny than the parts (housings like gearboxes and such) to clamp together.
Thus there is a need for designs that differ quite a bit from the conventional.
See the design principles listed on the page: RepRec pick-and-place robots (GemGum).

Under the lens of these constrains a particular set of
mechanisms/machine-elements emerges as especially promising.
This page is a collection of such mechanisms.

These mechanisms also allows for interesting 3D printable mechanics that
can cope without any metal screws whatsoever. A few big 3D printable screws suffice.

Related

• Gear-bearings. Peculiarly the periodic table of gearbearings
• The design principles listed on page RepRec pick-and-place robots (GemGum)

External links

Bearings and Gearings

• conical/tapered gearbeaings (with applied pre-tension)
• conical/tapered ravigneaux gearboxes: https://www.flickr.com/photos/65091269@N08/51163799216
• Wobblemotors: Moineau PCP pumps run partially in reverse with the core only rotating and the outside only wobbling
• PCP gearboxes based on the wobble-motor principle?
• ( Coupled cycloid wobble-rotors like this: https://twitter.com/Kuu3_Mechanics/status/1657680117680979969 – 9,10,11,12 )

• rotative to reciprocative conversion via a straight-line-hypocycloid rather than a classical crankshaft mechanism
  Like this: https://digital.library.cornell.edu/catalog/ss:29272012
  Or like this: https://commons.wikimedia.org/wiki/File:Inversion_of_Hypocycloid_Gear_Train_Ellipse_and_Straight-line_Mechanism.gif or [1]
  vice versa needs multi-phase drive for defined direction

Couplings

• https://en.wikipedia.org/wiki/Coupling#Oldham
• Oldham coupling inspired gear coupling:
  Two linear-rack-gearbearings with each two rollers to define a plane. Those two sandwiched atop each other with
  their rolling direction arranged 90° to each other. Thus they have the same exact effect as an Oldham coupling. But with internal rolling rather than sliding.
• (Schmidt coupling - this needs a lot of pins (ideally gear-bearings) thus listed in the likely unsuitable section further below)

CV type joints

• Tracta joint: https://en.wikipedia.org/wiki/Constant-velocity_joint#Tracta_joints
• Tripod joint: https://en.wikipedia.org/wiki/Constant-velocity_joint#Tripod_joints
• Double Cardan joint: https://en.wikipedia.org/wiki/Constant-velocity_joint#Double_Cardan
  Doube cardan is two universal joints that are each individually not CV
• (Rzeppa & Thompson down in the likely unsuitable section)

Joints

• Hirth joints: https://en.wikipedia.org/wiki/Hirth_joint <<< these are extremely useful
• Spline joints: https://en.wikipedia.org/wiki/Spline_(mechanical)

• fir-tree joints (generalization/optimization of dovetail joints) https://en.wikipedia.org/wiki/Dovetail_joint
• rotate extruded fir-tree-joints allowing for torsion or bending around a virtual axis

For quick-release:

• Panic snap: https://en.wikipedia.org/wiki/Panic_snap
• Snap shackle: https://en.wikipedia.org/wiki/Shackle

Chains

• Sprockets: https://en.wikipedia.org/wiki/Sprocket
• Roller chains: https://en.wikipedia.org/wiki/Roller_chain
• Gear teethed chains
• Attachment chains
• Rigid chains: https://en.wikipedia.org/wiki/Rigid_chain_actuator

For end-effectors and preceding

• Chucks https://en.wikipedia.org/wiki/Chuck_(engineering)
• Parallel plane fast acting grippers
• Vise like grippers: https://en.wikipedia.org/wiki/Vise

• Whippletree: https://en.wikipedia.org/wiki/Whippletree_(mechanism)
• Classical mechanical differential (for robot wrists): https://en.wikipedia.org/wiki/Differential_(mechanical_device)
• SCARA geomerty: https://en.wikipedia.org/wiki/SCARA
• Parallel manipulator: https://en.wikipedia.org/wiki/Parallel_manipulator
  The general principle. Not just the given example. Parallel SCARA, CoreXY, ... all parallel.
• successive onion shell peel-off tube-axle and bevel-gear serial mechanics principle

Special screwdrivers end-effector mechanisms that:

• put zero torque on the manipulated structure ("space screwdriver")
• decouple tensioning from unloaded screwing structure ports (wiki-TODO: explain that principle more clearly with sketch)

These screwdrivers end-effector mechanisms shall operate on "tension-force hydrants".
See ReChain frame systems.

Likely useful for tensioning and other things

• Turnbuckle: (but rather for length adjustment when load is displaced) https://en.wikipedia.org/wiki/Turnbuckle
• Differential screws: https://en.wikipedia.org/wiki/Differential_screw
• excenter tensioners
• knee-lever-tensioners (de: Kniehebelspanner) — <https://de.wikipedia.org/wiki/Kniehebel> — <https://de.wikipedia.org/wiki/Kniehebelpresse
• mechanisms that act as intended breakage points but that are reversible ...

• Rolamite (but modified to gearbearings): https://en.m.wikipedia.org/wiki/Rolamite

Positive displacement pumps

• PCP pumps: https://en.wikipedia.org/wiki/Progressing_cavity_pump
  Good resources for modeling here: http://www2.mat.dtu.dk/people/J.Gravesen/MoineauPump/HypoEpi4_3.html
  and here various configs: http://www2.mat.dtu.dk/people/J.Gravesen/MoineauPump/
• conventional piston pump: https://en.wikipedia.org/wiki/Piston_pump
  but operated like described on page vacuum handling
• ( Roots blower: https://en.wikipedia.org/wiki/Roots-type_supercharger )

Probably too many small pins, too low stiffness, and better solutions present

• Sarrus linkage: https://en.wikipedia.org/wiki/Sarrus_linkage
• Paucellier linkage: https://en.wikipedia.org/wiki/Peaucellier%E2%80%93Lipkin_linkage
• Schmidt coupling: https://en.wikipedia.org/wiki/Schmidt_coupling
• Classical cycloidal drive: https://en.wikipedia.org/wiki/Cycloidal_drive
  Very many bearings desirable here.

CV type joints:

• Rzeppa joint: https://en.wikipedia.org/wiki/Constant-velocity_joint#Rzeppa_joints
  2-DOF rolling balls not suitable for atomic scale due to atomic bumpiness.
• Thompsonjoint: https://en.wikipedia.org/wiki/Constant-velocity_joint#Thompson_joints
  Too intricate. Many small parts.